◇ TRAINING EDUCATION CENTERSmartSafe Education Centre
TEC Academy — training for your workshop
Professional training for operating and maintaining the complete SmartSafe equipment range — from 3D wheel alignment and ADAS calibration to IQ Scan diagnostics, ATF/AC stations and EV equipment. Practical, certified and tailored to your team.
All training takes place live at the SmartSafe Europe TEC Centre in Croatia.Practical knowledge for every device
Training that prepares your team for independent work
Certified trainers, small groups and real equipment — practical training your team can use immediately.
Training program
Courses organized by equipment area
Choose an area and review the available courses. Request any course through the contact form and we will arrange a suitable date.
Wheel Alignment & ADAS Calibration
2 coursesAdvancedIn person
Wheel Alignment & ADAS Calibration
A two-day professional course for service technicians, mechanics and diagnosticians — theoretical and hands-on competence in wheel alignment and ADAS calibration, with 15 modules and a 40% theory / 60% practice ratio.
- Wheel alignment — measurement and adjustment
- Vehicle preparation and mechanical-fault identification
- ADAS systems and when calibration is mandatory
- Static and dynamic calibration
- SmartSafe equipment and professional workflow
- Assessment, certificate and course code SS-EU-WA-ADAS-02
AdvancedIn person
Advanced 3D Alignment (WAA613)
A one-day advanced training for the automatic 3D aligner WAA613 with motorized column — handling complex cases, ADAS-referenced geometry and integration with calibration. Hands-on practice exclusively on the WAA613.
- Automatic camera lift (WAA613)
- Complex geometry cases
- ADAS-referenced geometry
- Database of 50,000+ models
- Integration with ADAS calibration
IQ Scan Diagnostics
2 coursesBasicOnline
IQ Scan — Basic Diagnostics
Basic training for IQ Scan diagnostics (IQ8-S2 / IQ10-S2) — reading and clearing faults, viewing live data and basic service functions.
- Connection and vehicle search
- Reading and clearing DTC codes
- Live data and graph view
- Basic service functions
- Saving and sharing reports
AdvancedIn person
Coding & Programming (IQ12-S2)
Online ECU programming and J2534 Pass-Thru in practice — coding, reprogramming and replacement of control units on modern vehicles, from the OEM order to a verified programmed ECU.
- J2534 architecture and OEM environment
- Safe flash of an existing module
- ECU replacement, coding and adaptations
- Online functions and recovery
- Failure classification and STOP conditions
ATF Stations
1 courseAdvancedIn person
ATF Service Equipment & Transmission Maintenance
A professional two-day universal (brand-neutral) course for service technicians — ATF service equipment and automatic transmission maintenance (AT, CVT, DCT). 18 modules, 14 contact hours, 50% practical work; held live at the SmartSafe Europe TEC center in Croatia.
- Universal brand-neutral program
- AT, CVT and DCT systems and service circuits
- OEM data and fluid specification verification
- Condition assessment and STOP criteria
- Controlled fluid exchange and level setting
- Equipment care and troubleshooting
AC Stations
1 courseIntermediateIn person
SmartSafe AC & EV Climate Academy
A practical two-day program for professional servicing of mobile air-conditioning systems using R134a and R1234yf refrigerants, with a dedicated module for electric and hybrid vehicles, electric compressors and safe work on high-voltage vehicles. 65% practical work; held live at the SmartSafe Europe TEC center in Croatia.
- Practical program for R134a and R1234yf
- Dedicated EV and hybrid module
- 65% practical work
- R1234yf and high-voltage safety
- AC519+, ECP739 and P03 equipment
- SmartSafe Academy certificate
EV Equipment
6 coursesBasicIn person
Fundamentals of electric and hybrid vehicles
Foundation level — 3 days / 24 hours. EV/HEV architecture, HV components and risks, safe vehicle intake, SmartSafe P03, basic measurements and checklist.
- MHEV, HEV, PHEV, BEV and fuel-cell vehicles
- HV battery, BMS, inverter, motor, DC/DC, OBC, contactors
- EV workshop safety: hazards, PPE and procedures
- Basic measurements and vehicle inspection
- SmartSafe P03 and RT100/IRT01
- Initial report and intake checklist
BasicIn person
Safe isolation and reactivation of HV systems
Foundation level — 3 days / 24 hours. Contactors, pre-charge, service disconnects, HVIL, Lockout/Tagout, absence-of-voltage confirmation, RT100/IRT01, practical exam and reactivation.
- HV contactors and pre-charge system
- Service disconnects and HV Interlock Loop
- Lockout/Tagout and absence-of-voltage check
- RT100 / IRT01 and insulation resistance
- Reactivation and final control
- Practical exam on isolation and reactivation
IntermediateIn person
Diagnostics of EV propulsion and energy systems
Advanced level — 3 days / 24 hours. Full scan, CAN/LIN/Ethernet, DTC, live data, actuation tests, DC/DC, OBC, inverter, motor, charging and signal analysis.
- Full-system scan and network topology
- CAN, LIN and Ethernet communication
- DTC analysis and live data
- DC/DC, OBC, inverter, motor and charging
- Oscilloscope, multimeter and current clamps
- Correlation of scan data with physical measurements
IntermediateIn person
HV battery diagnostics and condition assessment
Advanced level — 3 days / 24 hours. Battery construction, BMS, SOC/SOH/SOP, cell voltages, temperature deviations, insulation, capacity assessment, Battery Health Report and service decision.
- Pack construction and BMS/CMU
- SOC, SOH, SOP and degradation
- Cell voltages and temperature deviations
- Insulation resistance and pre-charge process
- Capacity assessment and Battery Health Report
- Decision: reuse, balancing or replacement
AdvancedIn person
Battery module service, balancing and capacity testing
Professional level — 3 days / 24 hours. Safe battery opening, module inspection, EB240/EB480, balancing, EP401, charge/discharge and reuse-or-replace decision.
- Safe opening of the battery pack
- Inspection of modules, connectors and busbars
- Cell balancing with EB240/EB480
- Charge/discharge and capacity test with EP401
- Identification of weak modules
- Reuse or replacement decision
AdvancedIn person
SmartSafe EV Professional — complex faults and final qualification
Professional level — 3 days / 24 hours. Intermittent HVIL and insulation faults, pre-charge/contactors, READY issues, AC/DC charging, BMS, overheating, professional service process, final theory and practical exam.
- Intermittent HVIL and insulation faults
- Pre-charge, contactors and READY issues
- AC/DC charging and BMS inconsistency
- Professional service process and reporting
- Final theory exam
- Final practical exam with an unknown fault
Sales and Portfolio
2 coursesIntermediateIn person
SmartSafe EV Portfolio Sales Specialist
A three-day course for sales managers — quickly identify the customer need, explain clearly what each SmartSafe EV device is used for, and build the right entry-level or professional equipment package.
- EV terminology and the EV workshop process
- Four groups of SmartSafe EV equipment
- Purpose, target customer and sales message for each device
- Customer discovery questions
- EV START, EV BATTERY SERVICE and EV PROFESSIONAL CENTRE packages
- Objection handling and a 10–15 minute demonstration
IntermediateIn person
SmartSafe Sales Product Academy
A two-day course for distributor sales teams — getting to know the complete SmartSafe portfolio, recognising workshop needs, selecting the right product or bundle, demonstrating value and correctly handing the customer over to technical and after-sales support.
- SmartSafe portfolio ecosystem and 9 equipment categories
- Target customer groups and the first qualifying question
- Natural cross-sell between categories
- 8-step sales methodology
- Live product demonstrations and sales cases
- Final Sales Challenge, certificate and a 30-day action plan
Why TEC Academy
Training that delivers measurable workshop results
Certified trainers
Instructors with field experience work through real workshop cases, not theory alone.
Small groups
Hands-on work in small groups with individual attention and enough time on the equipment.
Safety first
Special focus on high-voltage safety, environmental regulations and workplace protection.
Training certificate
Participants receive a certificate for successfully completed training on specific SmartSafe equipment.
Register your team
Ready to prepare your workshop?
Send an enquiry and we will arrange training tailored to your team, equipment and schedule — live at the SmartSafe Europe TEC Centre in Croatia.
